Leading 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Leading 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Blog Article

Don't ignore the forklift at the office. If the operation is bad, there will be serious accidents in minutes, and there are numerous mishaps involving forklifts.

Instance 1: The forklift cargo blocked the chauffeur's sight, and the individual ahead can not be located, leading to a rolling accident.
Instance 2: In order to keep the balance of the forklift when raising heavy items, the staff members used their body weight as the counterweight, which almost caused casualties.
Situation 3: The size of the forklift freight surpasses the allowed size of the route and hangs on the roadside rack, which virtually creates an crash.
Case 4: Forklift is speeding and surrender throughout a turn.
Instance 5: The forklift driver did not see the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the employees illegally, the forklift vehicle driver does not use the safety belt, the forklift lifter falls and the vehicle driver is crushed when the forklift rolls over.
Case 7: The forklift motorist did not put on a seat belt and fell from the vehicle when it rolled over and was squashed.
Forklift operation must take note of these issues ：.

Begin.
1. Before starting, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn first and then begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic pressure (air pressure) gauge must be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to initially confirm that the lots is steady and trusted.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole ought to be tilted in reverse. .
2. Do not lift the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is taking a trip, the fork needs to not be increased too high, which will certainly influence the stability of the forklift. .
3. After unloading, the fork needs to be reduced to the normal driving placement before driving. .
4. When turning, if there are pedestrians or lorries nearby, the driving signal needs to be provided first. High-speed doglegs are forbidden. High-speed sharp turns will cause the automobile to lose side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to turn off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to obey the web traffic rules in the manufacturing facility and must maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the tons must be in the most affordable placement that does not hinder the driving, and the gantry must be effectively tilted back. The load shall not be increased except when stacking or loading. .
8. The height of the load must not obstruct the motorist's view. In unique conditions, when the item impacts the forward vision, drive at a reduced speed when turning around.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is forbidden for employees to base on Stand-on Electric Pallet Stacker the fork to hold things and play a stabilizing duty. .
12. If problems are found, they will certainly be repaired and reported in a timely way, and they will never ever run with diseases or hide them.

filling and dumping.
1. When fork-loading products, the distance in between both forks need to be readjusted as required to make the load of both forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car should be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the tons, and it should be kept in mind that the fork tip must not touch various other goods or items. The load needs to be stabilized with very little back tilt of the gantry so that the tons does not move in reverse. The mast can be slanted onward slightly when the load is lowered to enable very easy placement of the load and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods Stand-on Electric Pallet Stacker or reduced the fork framework.
2. Draw the emergency brake take care of to dead or depress the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be examined, and fuel, lubricating oil and cooling water must be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak needs to likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you run into somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be as well sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers carry the goods and progress, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork operation is not enabled.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844